lseek - reposition read/write file offset
#include <sys/types.h> #include <unistd.h> off_t lseek(int fd, off_t offset, int whence);
lseek() repositions the file offset of the open file description associated with the file descriptor
fd to the argument
offset according to the directive
whence as follows:
The file offset is set to
The file offset is set to its current location plus
The file offset is set to the size of the file plus
lseek() allows the file offset to be set beyond the end of the file (but this does not change the size of the file). If data is later written at this point, subsequent reads of the data in the gap (a "hole") return null bytes ('\0') until data is actually written into the gap.
Since version 3.1, Linux supports the following additional values for
Adjust the file offset to the next location in the file greater than or equal to
offset containing data. If
offset points to data, then the file offset is set to
Adjust the file offset to the next hole in the file greater than or equal to
offset points into the middle of a hole, then the file offset is set to
offset. If there is no hole past
offset, then the file offset is adjusted to the end of the file (i.e., there is an implicit hole at the end of any file).
In both of the above cases, lseek() fails if
offset points past the end of the file.
These operations allow applications to map holes in a sparsely allocated file. This can be useful for applications such as file backup tools, which can save space when creating backups and preserve holes, if they have a mechanism for discovering holes.
For the purposes of these operations, a hole is a sequence of zeros that (normally) has not been allocated in the underlying file storage. However, a filesystem is not obliged to report holes, so these operations are not a guaranteed mechanism for mapping the storage space actually allocated to a file. (Furthermore, a sequence of zeros that actually has been written to the underlying storage may not be reported as a hole.) In the simplest implementation, a filesystem can support the operations by making SEEK_HOLE always return the offset of the end of the file, and making SEEK_DATA always return
offset (i.e., even if the location referred to by
offset is a hole, it can be considered to consist of data that is a sequence of zeros).
The _GNU_SOURCE feature test macro must be defined in order to obtain the definitions of SEEK_DATA and SEEK_HOLE from
The SEEK_HOLE and SEEK_DATA operations are supported for the following filesystems:
Btrfs (since Linux 3.1)
OCFS (since Linux 3.2)
XFS (since Linux 3.5)
ext4 (since Linux 3.8)
tmpfs(5) (since Linux 3.8)
NFS (since Linux 3.18)
FUSE (since Linux 4.5)
Upon successful completion, lseek() returns the resulting offset location as measured in bytes from the beginning of the file. On error, the value
(off_t) -1 is returned and
errno is set to indicate the error.
fd is not an open file descriptor.
whence is not valid. Or: the resulting file offset would be negative, or beyond the end of a seekable device.
whence is SEEK_DATA or SEEK_HOLE, and the file offset is beyond the end of the file.
The resulting file offset cannot be represented in an
fd is associated with a pipe, socket, or FIFO.
POSIX.1-2001, POSIX.1-2008, SVr4, 4.3BSD.
SEEK_DATA and SEEK_HOLE are nonstandard extensions also present in Solaris, FreeBSD, and DragonFly BSD; they are proposed for inclusion in the next POSIX revision (Issue 8).
See open(2) for a discussion of the relationship between file descriptors, open file descriptions, and files.
off_t data type is a signed integer data type specified by POSIX.1.
Some devices are incapable of seeking and POSIX does not specify which devices must support lseek().
On Linux, using lseek() on a terminal device fails with the error ESPIPE.
This page is part of release 4.15 of the Linux
man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.